Stop drafts, cut heating bills, and keep Clinton homes comfortable year-round.
Spray Foam Insulation in Clinton that seals every gap
Spray Foam Insulation in Clinton is the fastest way to close the air leaks that drive up your utility bill every winter. We install closed cell and open cell foam in attics, crawl spaces, rim joists, and walls for homes across Davis County. If your rooms feel drafty or your furnace runs nonstop, we can fix it.
Live phone supportUpfront optionsBacked workmanship
What's included
What our spray foam insulation service includes
Every Clinton spray foam job includes a full inspection, air sealing, and a clean walkthrough. We tell you upfront what is covered and what would be a separate project, like insulation removal or window replacement.
Thermal inspection and moisture test
We scan your attic, walls, and crawl space with a thermal imaging camera and check moisture levels with a meter. You see exactly where the air leaks are before we quote the job.
Air sealing at rim joists and bypasses
Closed cell foam goes into the rim joists, sill plates, and attic bypasses where most air leaks happen. This is the step that delivers the biggest energy savings in Clinton homes.
Closed cell or open cell application
We match the foam to the cavity. Closed cell for crawl spaces, rim joists, and exterior walls. Open cell for interior walls, attics, and sound control. You get the right product for the space.
Trim, cleanup, and debris removal
We trim cured foam with a utility knife, reinstall any removed insulation, and vacuum the work area. All debris leaves with us the same day. Your house is ready to use when we pull out.
Before-and-after thermal walkthrough
We walk the job with you and show the thermal camera reading before and after. You see the sealed assembly with your own eyes, not just on a report. Questions get answered on the spot.
Service overview
What Spray Foam Insulation in Clinton actually does
Spray Foam Insulation in Clinton is a two-part chemical foam that expands on contact to fill every crack, gap, and void in your building envelope. Unlike fiberglass batts that leave gaps around wires and pipes, foam grows into the space and hardens into an airtight seal. We spray closed cell foam where you need strength and moisture resistance, and open cell foam where you want sound control and a lighter R-value per inch. Both stop the air movement that makes Clinton homes feel cold.
Most Clinton homes were built before modern airtight standards, so they leak around rim joists, attic hatches, and sill plates. That leaking air pulls heat out of your living space and drives your furnace harder than it should. A Clinton UT spray foam insulation upgrade fixes the problem at the source instead of just adding more material on top. Homeowners in 84015 call us most often in October and November, right before the first hard freeze.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
How our spray foam installation process works
The process flexes to the condition, but these checkpoints keep decisions clear.
Phone assessment
We ask about your home's age, the problem areas, and your utility bills. You get a straight answer on whether spray foam is the right fix or whether blown-in insulation would serve you better. Most calls take under 10 minutes.
On-site inspection
A technician walks the attic, crawl space, and rim joists with a thermal imaging camera and moisture meter. We measure existing R-value, find air leaks, and check for moisture problems that need to be fixed first. You get a written scope and a fixed price before we start.
Prep and protection
We mask vents, lay drop cloths, and set up negative air pressure to keep fumes out of your living space. Our crew wears a respirator and protective suit during the spray. Pets and kids stay clear of the work zone for about four hours.
Foam application
We spray closed cell or open cell foam in lifts, letting each pass cure before the next. Attics typically take three to five hours; crawl spaces and rim joists run two to four hours. The foam expands roughly 30 to 60 times its liquid volume to fill every gap.
Trim and walkthrough
Once cured, we trim excess foam with a utility knife, reinstall any removed insulation, and walk the job with you. You see the thermal camera reading before and after. We leave the space clean and ready to use.
Tools & methods
Tools and methods we use
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Spray foam gun
Our primary application tool. We use a heated, plural-component gun that mixes the two foam chemicals at the tip for a consistent, even spray.
Thermal imaging camera
We use it before and after every job to find air leaks and verify the seal. You see the before-and-after images on the walkthrough.
Moisture meter
Checks framing and substrate moisture before we spray. Sealing a wet cavity traps moisture and causes mold, so this step is non-negotiable.
Blown-in insulation machine
Distributes cellulose or fiberglass evenly over the spray foam air seal in open attics to reach target R-values at a lower cost.
Respirator and protective suit
Required OSHA personal protective equipment during application. We keep the work zone sealed and ventilated so fumes stay out of your living space.
Utility knife and insulation tape
Used to trim cured foam flush with framing and seal seams on foam board and reflective foil installations.
Use cases
When Clinton homeowners call for spray foam
These examples show how the service framework adapts rather than forcing every call through one repair.
Crawl space moisture and mold
A Sunset Heights home had mold growing on the crawl space joists and cold floors above. The old fiberglass batts were sagging and wet from ground moisture. → We removed the wet insulation, dried the framing, and sprayed closed cell foam on the crawl space walls and rim joist. Moisture readings dropped from 22 percent to 11 percent, and the floors are warm.
Metal shop condensation
A shop building in the Clinton Industrial Park dripped water on tools and equipment every winter. The metal roof deck had no insulation and condensed constantly. → We sprayed 2 inches of closed cell foam on the roof deck and wall girts. Condensation stopped completely, and the building holds heat with a fraction of the propane.
Problems we solve
Problems spray foam insulation solves in Clinton
Most Clinton homes have at least one of these issues. Spray foam fixes them at the source instead of masking the symptom with more material.
High energy bills every winter
We seal the attic floor and rim joists with closed cell foam, then verify the air barrier with a thermal camera. Most customers see a 20 to 30 percent drop in heating costs.
Cold floors and drafty rooms
Closed cell spray foam at the rim joist and crawl space walls stops the airflow. Floors warm up within hours, and the house holds heat through the night.
Moisture, mold, and condensation
Closed cell foam acts as a vapor retarder and air barrier in one. We test moisture before and after, and we will not seal a wet cavity until it is dry.
Frozen pipes and ice dams
We seal the roof deck and attic bypasses with spray foam so warm air stays inside the house. That stops the melt-freeze cycle that causes ice dams.
Pricing process
Spray foam insulation cost in Clinton
$1,800 - $6,500 depending on scope
Square footage
The single biggest cost driver. A 1,200-square-foot attic takes about half the material of a 2,400-square-foot attic, and labor scales with it.
Foam type
Closed cell foam costs more per board foot than open cell because of its higher density and R-value. We use closed cell where it matters and open cell where it does not.
Access and prep
Crawl spaces with tight access or attics full of stored items take longer to prep and protect. That adds labor time but not material cost.
How much does spray foam insulation cost in Clinton UT?
Most Clinton spray foam jobs run $1,800 to $6,500 in 2026, depending on square footage and foam type. Attic-only projects typically land between $2,200 and $4,000. Crawl space and rim joist work often costs less. Closed cell costs more per board foot than open cell, but it delivers a higher R-value per inch.
Is spray foam insulation worth it in Clinton Utah?
Yes, if your home has air leaks or under-insulated areas. Most Clinton customers see a 20 to 30 percent drop in heating and cooling costs, which pays back the investment in three to five years. If your attic already has adequate R-value and no air sealing problems, we will tell you that instead of selling you foam you do not need.
What is the R-value of spray foam in Clinton UT?
Closed cell spray foam delivers about R-6.5 to R-7 per inch, and open cell delivers about R-3.5 to R-3.8 per inch. A 2x6 wall cavity filled with closed cell foam reaches roughly R-21. The U.S. Department of Energy recommends R-49 to R-60 for Clinton attics, which we hit with a combination of foam and blown-in insulation.
Can spray foam insulation be installed in Clinton winter?
Yes, we install spray foam year-round in Clinton, including through January and February. Cold weather slows the curing reaction, so we pre-heat the substrate and use winter-grade foam formulations rated down to 20 degrees Fahrenheit. We schedule cold-weather jobs for mid-day when attic temperatures peak.
Related services
Related Services
Attic Insulation
Spray foam and blown-in insulation work together in Clinton attics. We seal the attic floor with foam first, then add blown-in insulation to hit the R-49 target that Davis County homes need for winter.
Garage Door Insulation
An uninsulated garage door can drop your garage temperature by 20 degrees. We pair foam board or reflective foil on the door with spray foam at the garage ceiling to stop cold air from bleeding into the house.
Fiberglass Insulation
Fiberglass batts still have a place in interior walls where air sealing is not the priority. We install Johns Manville and Owens Corning batts alongside spray foam to keep project costs down without sacrificing performance.Ready when you are
Get Spray Foam Insulation in Clinton before the freeze
Fall is the busiest season for spray foam in Clinton, and slots fill fast. Call now for a free estimate and a fixed price. We are licensed, insured, and we warranty our workmanship. One call and your drafts are gone.
Talk with the local team
Request Spray Foam Insulation
Call (855) 927-7517 or email info@sealwisevale.com and we will get you on the schedule. We answer the phone during business hours and roll a truck after hours for emergencies like frozen pipes or storm damage. Most estimates are booked within a day or two.