Batts, rolls and blown-in fiberglass installed code-correct in Clinton, UT
Fiberglass Insulation in Clinton that stops the drafts
Fiberglass Insulation in Clinton is the fastest way to stop cold rooms, high bills and frozen pipes in a Davis County home. We install Owens Corning and Johns Manville batts, rolls and blown-in fiberglass in attics, walls and crawl spaces across Clinton, UT 84015. If your upstairs runs 8 degrees colder than your main floor, we can fix that this week.
Live phone supportUpfront optionsBacked workmanship
What's included
What our fiberglass install covers
Every fiberglass job we run in Clinton includes the prep work that makes the insulation actually perform. Here is what is in the scope, and what we quote separately if your attic needs it.
Attic and wall inspection
Thermal imaging camera and moisture meter scan of every accessible cavity. You get photos, R-value readings and a written target before we quote a dollar of work.
Air sealing at penetrations
Top plates, can lights, plumbing chases, chimney gaps and wiring holes get sealed with foam and caulk before any fiberglass goes down. This is the step most competitors skip.
Fiberglass batt and roll install
Owens Corning and Johns Manville batts cut with a fiberglass batt knife, friction-fit between joists, with kraft facing or vapor barrier stapled tight and continuous.
Blown-in fiberglass topping
Loose fiberglass run through the insulation blower to fill irregular bays, around wiring, and over the top of existing batts to hit your target R-value at a consistent depth.
Vapor barrier and tape
Where code or moisture conditions call for it, we install a vapor barrier and seal seams with insulation tape so warm moist air never reaches the cold side of the assembly.
Cleanup and verification
We bag all offcuts, vacuum the access path, and re-scan with the thermal camera. You walk the attic with us and see the before and after on the same screen.
Service overview
Fiberglass Insulation in Clinton, Utah
Fiberglass Insulation in Clinton is mineral-fiber material, spun from glass into batts, rolls or loose fill, that traps air and slows heat movement through your attic, walls and floors. We cut it to fit between joists and studs, seal the gaps around it, and set the R-value to what your assembly needs. It is the workhorse of Utah homes because it is affordable, fire-resistant and holds its shape for decades when it stays dry.
Clinton homes take a beating from both ends of the thermometer. Summer attic decks hit 140 degrees, and January nights drop into the teens, so weak insulation shows up fast as ice dams, drafty rooms and $200-plus winter gas bills. If you have been searching fiberglass insulation near me Clinton and getting nothing but national lead-gen pages, we are the local crew that actually shows up in Davis County.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
How our fiberglass install runs
The process flexes to the condition, but these checkpoints keep decisions clear.
Attic inspection
We walk your attic, walls and crawl space with a thermal imaging camera and moisture meter. You get photos of every gap, wet batt and thin spot, plus a written R-value target for your assembly. Takes 45 minutes, costs nothing.
Air sealing first
Fiberglass only works when air stays put. Before any batt goes down, we seal top plates, can lights, plumbing chases and chimney gaps with foam and caulk. This single step is why our jobs outperform the box-store DIY version.
Batt and roll install
We cut Owens Corning and Johns Manville batts with a fiberglass batt knife, friction-fit them between joists, and staple the kraft facing or vapor barrier tight. A 1,200 sq ft attic takes our two-man crew four to six hours.
Blown-in topping
Where coverage is uneven or joists are buried, we run the insulation blower and top off with loose fiberglass to hit your target R-value. Blown-in fills around wires and pipes better than batts alone, so we often combine both.
Final verification
We re-scan with the thermal camera, check depth at six points, and hand you the R-value readings. You see the before and after on the same screen before we pack up. No invoice until you have walked it with us.
Tools & methods
Tools and methods we use
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Thermal imaging camera
Finds missing batts, air leaks and cold spots in Clinton walls and ceilings before we quote. You see the same image we do.
Moisture meter
Checks every cavity for trapped water before we cover it. Wet fiberglass has to come out, no exceptions.
Insulation blower
Runs loose fiberglass into irregular attic bays, around wiring and over existing batts to a consistent depth.
Fiberglass batt knife
Cuts Owens Corning and Johns Manville batts clean to fit between joists and studs without compression.
Staple gun
Fastens kraft facing and vapor barrier tight and continuous so air never bypasses the insulation.
Respirator and protective suit
OSHA-compliant protection for our crew during install so no fibers migrate into your living space.
Spray foam gun
Seals top plates, rim joists and penetrations with Great Stuff and Dow foam before fiberglass goes down.
Use cases
When Clinton homes need fiberglass
These examples show how the service framework adapts rather than forcing every call through one repair.
Frozen kitchen pipe in Downtown Clinton
A 1968 ranch with zero insulation in the exterior kitchen wall cavity. The supply line froze and burst twice in two winters, flooding 200 gallons into the basement both times. → We opened the sheathing, packed fiberglass batt insulation into the bay, sealed the cavity, and added heat tape on the vulnerable run. The wall held through a 9-degree January night with no freeze.
Sweating metal shop in Clinton Industrial Park
A 2,400 sq ft metal building with bare steel purlins. Condensation rained off the roof every winter, rusting tools and making the floor slick and unusable. → We installed vinyl-faced fiberglass rolls between the purlins and girts and taped every seam. The interior stayed dry through the winter and the shop is now usable year-round.
Problems we solve
Clinton insulation problems we fix
Most Clinton attics we open have the same three or four failures. Here is what they look like, what they cost you, and how we correct them.
Compressed or missing attic batts
We pull the dead batts, air seal the top plates, and blow in or lay new fiberglass to R-49. That single fix usually cuts winter heat loss through the ceiling by about 70 percent.
Frozen pipes in exterior walls
We open the wall cavity, pack fiberglass batt insulation Clinton code requires into the bay, seal the sheathing, and add heat tape on the vulnerable run. No more 2 a.m. calls.
Ice dams on the roof edge
We insulate the attic floor to R-49 and verify the soffit and ridge venting, so the roof deck stays cold and snow melts evenly off the edge instead of backing up.
Mold and moisture in crawl space batts
We remove the wet material, dry and treat the cavity, install a proper vapor barrier, and reinstall faced fiberglass with the barrier facing up. We check with a moisture meter before we close it up.
Pricing process
What fiberglass insulation costs in Clinton
$1,300 - $2,200 for a typical 1,200 sq ft Clinton attic at R-49
Attic square footage
Material and labor scale directly with area. A 1,200 sq ft attic takes about half the material of a 2,400 sq ft one, and the per-square-foot price drops slightly on larger jobs.
Target R-value
Going from R-19 to R-49 takes roughly three times the material of a simple top-off. We tell you the cost difference between hitting code minimum and going deeper.
Air sealing scope
A handful of can lights is a quick seal. A dozen plumbing chases, a chimney and a kneewall take longer, and that labor shows up in the quote.
How much does fiberglass insulation cost in Clinton UT?
Typical 2026 pricing in Clinton runs $1.10 to $1.80 per square foot installed for attic batts, or $1,300 to $2,200 for a 1,200 sq ft attic at R-49. Wall cavity work costs more per square foot because of the labor. Blown-in attic topping is the cheapest option at $0.90 to $1.40 per square foot.
Is fiberglass insulation safe for Clinton Utah homes?
Yes, when it is installed correctly and stays dry. Modern Owens Corning and Johns Manville fiberglass uses formaldehyde-free binders, and we wear respirators and protective suits during install so no fibers end up in your living space. The real health risk in Clinton attics is trapped moisture and mold, which is why we check with a moisture meter before covering anything.
What R-value fiberglass insulation for Clinton UT?
Clinton sits in climate zone 5B, so Utah code calls for R-49 to R-60 in attics, R-13 to R-15 in 2x4 walls, R-20 to R-21 in 2x6 walls, and R-30 in floors over crawl spaces. We measure your existing depth and tell you exactly how many inches of fiberglass you need to hit the target.
Fiberglass vs spray foam insulation in Clinton Utah?
Fiberglass costs roughly one-third of spray foam and handles the average Clinton attic fine. Spray foam wins in crawl spaces, rim joists and any spot with air leaks you cannot seal by hand, because it air-seals and insulates in one pass. Many Clinton homes get the best result from both: foam at the penetrations, fiberglass across the field.
Related services
Other insulation work we handle
Spray Foam Insulation
We pair spray foam with fiberglass in Clinton crawl spaces and rim joists, sealing the air leaks that fiberglass alone cannot stop. Foam goes on first at the penetrations, then fiberglass fills the field.
Attic Insulation
Attics are where most Clinton fiberglass work happens. We remove old compressed batts, air seal, and blow in or lay new fiberglass to R-49 or better, matched to your joist depth and venting.
Garage Door Insulation
An uninsulated garage door in Clinton can radiate 20 degrees of cold into an attached garage. We add foil-faced or fiberglass door kits so the garage stays above freezing and the wall between it and your house works.Ready when you are
Get your Clinton fiberglass quote this week
One free attic inspection, one upfront number, no fuel or disposal fees tacked on at the end. We are licensed, insured and local to Davis County. Call now and we will have your R-value target and a written quote in your hands within 48 hours.
Talk with the local team
Request Fiberglass Insulation
Call (855) 927-7517 or email info@sealwisevale.com and we will get you on the schedule. We answer the phone during business hours and roll a truck after hours for emergencies like frozen pipes or storm damage. Most estimates are booked within a day or two.